A little improvement on my IPv6 setup. I discovered a handy configuration parameter for RADV that makes it unnecessary to update the configuration file in the rare occasion my IP address changes. The improved /etc/radvd.conf looks like this:

interface eth0
{
        AdvSendAdvert on;
        MinRtrAdvInterval 30;
        MaxRtrAdvInterval 100;
        prefix 0:0:0:1::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                AdvRouterAddr off;
                Base6to4Interface eth1;
        };

};

Posted at: 17:54 | Category: /fedora | permalink

After hearing about the activation of IPv6 (AAAA) records for four of the root DNS servers I got very curious about IPv6 and its current state of adoption. Well, it turns out IPv6 may not be the solutions to all Internet woes but we will have to learn to live with it anyway.

And so I did. Like 99.999% percent of Internet users I don't have a native IPv6 connection, but enabling a IPv6 tunnel on Fedora is very, very easy. I decided for the simplest type of tunnel, called 6to4. This type of tunnel is very convenient as I don't need to register it anywhere nor do I need to ask permission to anyone. It is based on the kindness of people that run 6to4 routers in the IPv4 Internet at the 192.88.99.1 anycast address. Usually people disregard this type of tunnel as being slow, but routing from Brazil to the world is already so slow I found the performance acceptable. Besides, there isn't much yet to do in the current IPv6 Internet.

Enabling a 6to4 tunnel on Fedora is ridiculously simple. First put the following lines in /etc/sysconfig/network:

NETWORKING_IPV6=yes
IPV6_DEFAULTDEV=tun6to4
IPV6FORWARDING=yes

The last line is only required if you are going to share the IPv6 connection with a local network. The rest of this recipe assumes you are. Now find the configuration file for the interface connected to the Internet. If it is eth1 the file should be /etc/sysconfig/networking/devices/ifcfg-eth1. Put the following lines there:

  IPV6INIT=yes
  IPV6TO4INIT=yes
  IPV6_CONTROL_RADVD=yes
  IPV6TO4_ROUTING="eth0-:1::1/64 wlan0-:2::1/64"

Once again, the last two lines are only required if you have a local network you want to provide with IPv6 connectivity. If not, remove the extra lines and you are set. Restart the interface and you are connected to the IPv6 Internet! When using 6to4, probably due to the performance concerns, Fedora prefers IPv4 addresses. So, go to a IPv6 only site (like http://www.ipv6.bieringer.de/) to test it. And remember to define a IPv6 firewall. Your current iptables firewall only covers IPv4, use ip6tables to create a IPv6 one.

A nice thing about this setup is that a 6to4 tunnel gives me a whole /48 netblock based on my IPv4 address. So, no NAT in my local IPv6 network! The last two lines lines above allow the networking scripts to control the RADV daemon and to create IPv6 addresses to other interfaces (besides the one you are actually configuring). Just treat the /48 of your 6to4 address as a prefix and create a /64 netblock for each interface. Create a /etc/radvd.conf file with an entry like this for each interface:

interface eth0
{
        AdvSendAdvert on;
        MinRtrAdvInterval 30;
        MaxRtrAdvInterval 100;
        prefix 2002:XXXX:XXXX:1::/64
        {
                AdvOnLink on;
                AdvAutonomous on;
                AdvRouterAddr off;
        };

};

Where 2002:XXXX:XXXX is your automatically configured 6to4 adress. Start RADV daemon and the hosts in you internal network should receive an automatically generated address.

For me, the next step would be to do the same to this site and add a little bit more content to the IPv6 Internet. Unfortunately, the Xen kernel used by my VPS provider doesn't support stateful iptables support for IPv6. I though IPv6 support on Linux was a done deal, but this critical functionality was only added about and year ago in kernel 2.6.20. It seems IPv6 may be a bit farther in the future than I expected. But it was surely fun to set it up anyway.

Posted at: 19:27 | Category: /fedora | permalink

I've been running Fedora 8 for the last couple of weeks. If nothing else, using Fedora is a constant source of fun. Always new toys to play with, old bugs fixed, new bugs created. And obviously, new tricks to be learned.

PulseAudio is one of the great features introduced in Fedora 8. I really enjoyed the good work that went into integrating PulseAudio and Fedora. It really is seamless, except for the odd bug in alsa and proprietary applications. Here are two things I discovered regarding pulse audio.

First: PulseAudio shows a simplified but functional interface to control sound, and to support Alsa applications transparently, it appears as the default virtual device hiding you hardware device. Problem is, if the hardware device is muted or has the volume set too low, there is nothing you can do through the PulseAudio interface to make sound work. Obvious as it seems, you have to first enable and adjust the volume of the relevant inputs in the hardware device, and then be able to enjoy PulseAudio. You can use the alsamixer -c [0...7] command, changing the -c argument until you find your hardware device, set it up, and you are ready to go. The good news is that, once it is done, applications (such as Skype) won't be messing with your hardware device as PulseAudio hides it.

Second: to enable the PulseAudio daemon in you GNOME session, you need to go to System|Preferences|Hardware|Sound and enable ESD. That's really stupid, they should have changed the label, but this control really creates an instance of the PulseAudio daemon. If it isn't running, sound won't work. I discovered this because ESD gave me a lot of problems in the past and have been deactivated in my GNOME preferences for a long time. It never occurred to me to enable it to fix Alsa applications that suddenly stopped working. But, again, once you discover that, everything just works.

Posted at: 22:59 | Category: /fedora | permalink

The version of K9Copy packaged by Livna is now newer than the one I maintained, so I'm officially taking it down.

Posted at: 17:20 | Category: /fedora | permalink

Both OpenMSX and K9Copy now have official RPMs for Fedora. OpenMSX is part of the main distribution, just execute yum install openmsx. K9Copy is packaged by Livna, go there and install their repo.

As my version of K9Copy is newer than the one packaged by Livna, I will keep it a bit longer. When Livna catches up, I will remove it from the site. See, I actually like being obsoleted. :)

Posted at: 17:57 | Category: /fedora | permalink

I've updated my RPM package for K9Copy to the 1.1.3 release. Get it here.

Posted at: 11:46 | Category: /fedora | permalink

If you want to copy a dual layer DVD to a single layer one in Linux, you will very pleased to know K9Copy. This is a nice utility that removes unwanted extras and/or requantizes the main title while preserving the menu structure.

As it isn't available in the Livna repository, I created a RPM of it for Fedora. Check the K9Copy RPM link in the nav bar.

Posted at: 16:42 | Category: /fedora | permalink